Windows, Siding & Insulation

Soffit Calculator

Measure the actual soffit runs and required cut depth. Compare area coverage with the number of complete strip cuts that fit in a stock panel; area alone can understate the purchase.

Make it yours

Your numbers

Start with the example below, then adjust it to your home.

selection
selection
ft
ft
in

Measure the actual required cut. No installation gap is assumed.

selection
selection
%

Applied once to area, or once to required cut pieces. The two estimates are alternatives, not added together.

Assumptions and overrides
$ / stock piece
sq ft

Area estimate only; do not count decorative faces as separate stock panels.

in
in
in

Example 1/8-inch kerf. A final piece using the full remaining stock needs no extra end cut.

selection
sq ft

Only areas not already included in the measured runs. Extra shapes get a separate area allowance, not a verified cut layout.

selection
Your numbers stay in your browser.
A clearer picture

Planning stock purchase

22panels / sheets
Modeled eave run
140 ft
Soffit area including entered extras
210 sq ft
Area with additional allowance
231 sq ft
Area-only coverage estimate
20 panels / sheets
Area-only budget
$160.00
Crosscut pieces across runs
140 cuts
Cuts with additional allowance
154 cuts
Complete pieces per stock panel
7 pieces
Cut-yield stock estimate
22 panels
Planning stock material budget
$176.00
Updates as you adjust your numbers

An estimate, not a quote. Example rates are adjustable. See the assumptions below.

Estimate basis

Area alone suggests 20 panels; the strip-cut estimate is 22. The planning purchase uses the larger count. This is not a guaranteed cut list for corners, joints, defects, or arbitrary offcut reuse.

The additional allowance is for extra purchase contingency after modeled cut yield, not a second kerf allowance. Set it to zero when you do not need an additional contingency.

Behind the numbers

How this calculator works

Rectangular run = 2 × (length + width), or use measured total eave length at one uniform depth. Area = run × depth in feet + additional measured corner/return sq ft. Area-only stock = ceil(area × (1 + allowance / 100) / effective coverage). Strip cuts = sum of ceil(each run / effective panel width). Pieces per stock = floor((stock length + kerf) / (cut depth + kerf)). Cut stock = ceil(ceil(cuts × (1 + allowance / 100)) / pieces per stock) + separate area stock for measured extras. Planning purchase = larger of area and cut estimates; material budget = stock × entered unit price.

A worked example

40 × 30 ft, all four sides, at 18-in depth gives 210 sq ft; 10% extra gives 231. The reference area-only counts are 20 vinyl panels ($160 at $8), 20 aluminum panels ($240 at $12), or eight 32-sq-ft plywood sheets ($200 at $25). With the default 1/8-in kerf, the strip model instead needs 22 vinyl panels ($176). Counterexample: a 120-ft run, 50-in cut, 12-in effective width, 144-in stock, zero kerf/extra has 500 sq ft and an area-only 42 panels, but 120 cuts at two per panel require 60 panels.

Assumptions & what’s included

  • Rectangular mode assumes soffit on all four sides; a house perimeter is not automatically the actual eave run. Gable/rake edges are not added. P × depth does not include every exterior corner square. Enter only additional measured corner/return areas not already included. Total-length mode requires uniform depth and treats the total as one run; estimate disjoint runs or different depths separately.
  • Strip stock dimensions are usable trimmed stock. Kerf is lost between successive pieces; a final piece consuming the remaining full length needs no extra end cut. End trimming, gaps, splices, defects, and general nesting are not modeled. A cut longer than stock is rejected. Effective width is the installed panel coverage, not the count of decorative faces.
  • Vinyl/aluminum examples: 12-ft stock × 1-ft effective width, 12-sq-ft area coverage, prices $8 / $12. Plywood example: 32-sq-ft sheet at $25. Replace all with actual product specifications. Additional corners use separate area stock, not a verified cut layout. No ventilation or net-free vent-area certification, universal vent pattern, or expansion-gap prescription is provided.
  • Dimensions are normalized to feet and square feet; changing display units preserves the physical measurement. Inputs have explicit finite limits. Missing active inputs are errors, while an explicitly entered zero price is valid.
  • Full precision is retained until display. Money displays to cents using half-up rounding for these nonnegative costs; individually rounded lines may differ by a cent from their sum. Discrete purchases round upward before display, without subtracting an epsilon. Siding squares remain an area measure.
  • Defaults and reference price, weight, productivity, burden, markup, and fee allowances are adjustable examples observed November 16, 2026, not verified current supplier prices or universal recommendations. Confirm product labels, scope, and written quotes before ordering.

A few common questions

Why is the cut estimate larger than the area estimate?

A panel can have enough total area but leave unusable lengths after crosscutting. The tool counts complete cuts across each entered run and complete pieces per stock panel, then uses the larger purchase estimate.

Can I enter eaves with different overhang depths?

The total-length mode supports one uniform depth. Calculate each depth/run separately and review stock pooling and corners before ordering; arbitrary offcut reuse is not modeled.