Insulation Cost Calculator
Select an insulation family and enter a matching product specification. Use whole bags, physical spray-foam thickness, or layered sheets as appropriate; equal surface area does not imply equal thermal performance.
Your numbers
Start with the example below, then adjust it to your home.
Base planning estimate / entered quote
- Net installed surface area
- 1,000 sq ft
- Lower wage scenario
- $2,709.72
- Higher wage scenario
- $3,017.52
- Base cost per unit
- $2.91 / sq ft
- Materials
- $1,310.00
- Supplies allowance
- $150.00
- Installation labor
- 20 person-hours
- Base employee wage
- $26.32 / hour
- Base burdened labor
- $789.60
- Fixed allowances total
- $175.00
- Base subtotal before markup
- $2,424.60
- Base contractor markup
- $484.92
An estimate, not a quote. Example rates are adjustable. See the assumptions below.
Estimate basis
Wage basis: United States; BLS OEWS May 2025, Insulation Workers, Floor, Ceiling, and Wall (47-2131).
Wage data retrieved 2026-11-16; reference allowances observed 2026-11-16. Material prices, hours, fees, burden, and markup are editable illustrative planning assumptions, not surveyed current local prices.
Lower/base/higher vary employee wages and their markup only. Base uses the mean, not median; the other scenarios use occupational P25/P75. These are not confidence intervals or contractor-bid ranges.
How this calculator works
Component total = (materials + installed sq ft × supplies rate + person-hours × insulation-worker employee wage × burden + fixed allowances) × (1 + markup / 100). Batts: materials = area × selected R allowance; hours = area × 0.02. Blown: materials = whole chart bags × bag price; hours = bags × entered person-minutes / 60. Spray: board feet = sq ft × thickness in inches; materials = board feet × material rate. Boards: sheets = ceil(adjusted area / sheet coverage) × ceil(target R / sheet R); labor uses selected surface-area or per-layer basis. All-in spray quote = board feet × all-in rate, with nothing added. Per-unit cost divides by net installed sq ft.
1,000 sq ft of R-30 batts: $1,310 materials, $150 supplies, 20 person-hours, and $175 fixed. Manual reference insulation wages $19.68 / $24.61 / $27.97, 1.5× burden, and 20% markup produce $2,670.48 / $2,847.96 / $2,968.92. A separate synthetic foam example is 1,000 sq ft × 3 inches = 3,000 board feet; an entered material-only $0.50/board-ft test rate gives $1,500 materials, not a market quote.
Assumptions & what’s included
- Illustrative fiberglass batt material rates per sq ft: R-13 $0.68, R-19 $0.83, R-30 $1.31, R-38 $1.62; labor 0.02 person-hours per sq ft. Unsupported R tiers are rejected. Custom allowances replace the selected preset explicitly.
- Family supplies per sq ft / combined fixed dollars: batt $0.15 / $175, blown $0.10 / $325, spray $0.25 / $350, rigid $0.20 / $200. Fixed budgets combine equipment, preparation, and cleanup; they exclude removal of existing insulation and hazardous materials. Supplies are not a universal vapor-barrier prescription.
- Blown labor defaults to five person-minutes per whole purchased bag, not elapsed crew time. Quantity-tool comparisons must use identical product rows and purchasing allowances: quantity defaults to 5%, this cost tool to 0%. No current bag price is bundled.
- Open-cell/closed-cell spray foam requires thickness and a compatible rate. One board foot is one sq ft at one inch thickness, not a cubic foot. Material-only mode also requires a labor assumption. All-in quote mode adds no labor, burden, supplies, fixed fees, or markup. Foam type alone makes no R claim.
- Rigid-board sheets use required label R/thickness and actual coverage; price is per sheet. Labor defaults to an illustrative 0.025 person-hours per sq ft per layer, or you may explicitly select finished-surface labor. Counts and material costs grow with layers; no nesting optimization or offcut reuse is promised.
- Nominal product R-values and thicknesses describe the selected product, not whole-assembly performance. Ideal layering requires compatible, properly installed, uncompressed products and adequate space. This tool does not certify cavity fit, code compliance, structural loading, or moisture design.
- The AttiCat US open-attic chart was retrieved 2026-11-16 from Owens Corning (27.5-lb bag). Its webpage has no explicit revision identifier; verify the current bag label. Only published R rows are supported. The strictest minimum-bag, maximum-coverage, or minimum-weight requirement controls. Minnesota adds the published supplemental depth and bags. This application choice is independent of wage location.
- Cellulose and other loose fill require an actual bag-label row: R, minimum bags per 1,000 sq ft, bag mass, initial depth, and settled depth, plus any maximum-coverage/minimum-weight columns. Greenfiber's current chart was inaccessible during verification, so no unverified Greenfiber production preset is supplied. Initial and settled depths are separate; no second settlement factor is added.
- Additional purchasing allowance increases bought material only; it cannot establish the required installed thickness. No interpolation or extrapolation of coverage tables is performed. Board sheet coverage is not a cutting-layout solution.
- Wages are employee hourly data from BLS OEWS May 2025, retrieved November 16, 2026. State/territory selections are not ZIP or city estimates and do not change material prices. Missing or suppressed occupation data falls back to the entire national wage series with an explicit notice. Manual employee wages remain available.
- Lower/base/higher vary only wages: occupational P25, mean, and P75. The mean is not a median and may fall outside the percentiles; scenarios are neither confidence intervals nor the full range of bids. Burden multiplies employee wages; markup then applies to the subtotal. Do not enter an all-in contractor rate as a wage.
- No tax, contingency, financing, or unlisted delivery is added. Fixed allowances are editable budgets, not local permit requirements or estimates for hazardous-material work. Project quantity must be positive, even if fixed fees have been entered.
- Dimensions are normalized to feet and square feet; changing display units preserves the physical measurement. Inputs have explicit finite limits. Missing active inputs are errors, while an explicitly entered zero price is valid.
- Full precision is retained until display. Money displays to cents using half-up rounding for these nonnegative costs; individually rounded lines may differ by a cent from their sum. Discrete purchases round upward before display, without subtracting an epsilon. Siding squares remain an area measure.
- Defaults and reference price, weight, productivity, burden, markup, and fee allowances are adjustable examples observed November 16, 2026, not verified current supplier prices or universal recommendations. Confirm product labels, scope, and written quotes before ordering.
A few common questions
Why must I enter a bag, foam, or board price?
A usable current product price was not verified. An explicit manual value makes the pricing basis reviewable; blank is not silently treated as zero. Enter zero only when that is your intended assumption.
Will the tool add labor to my installed foam quote?
No. Choose All-in installed quote to multiply the entered rate by board feet only. Wage, burden, supplies, fixed fees, and markup controls are inactive in that mode.
