Roofing

Roofing Calculator

Separate actual roof geometry from purchasing allowances. Estimate broad material quantities first, then use product-specific coverage and independent edge measurements before ordering.

Make it yours

Your numbers

Start with the example below, then adjust it to your home.

selection
ft
ft
selection
in

Horizontal projection, including gable ends; not a sloped fascia measurement.

selection
in / 12 in
selection
%
Assumptions and overrides
$ / 100 sq ft

Illustrative material-only allowance; not an installed quote or rounded package purchase.

lb / 100 sq ft

Area-based purchasing weight, not a structural-load assessment or actual package weight.

selection
bundles

Use the selected product specification. Three is an example, not a rule for every shingle.

selection
selection
sq ft / roll

Illustrative effective coverage after required laps; replace with the selected assembly's specification.

layers
%

Not field-shingle waste. Do not include laps again if effective coverage already accounts for them.

selection
ft
ft

Zero is an arithmetic example only. Enter the applicable product lap; offcuts are not reused between runs.

selection
Your numbers stay in your browser.
A clearer picture

Field purchasing squares

17.28100 sq ft
Actual roof surface
1,502.64 sq ft
Actual roofing squares
15.03 100 sq ft
Field purchasing area
1,728.03 sq ft
Field asphalt bundles
52 bundles
Coverage of whole field bundles purchased
1,733.33 sq ft
Separate underlayment area
1,502.64 sq ft
Underlayment rolls
4 rolls
Total measured or derived roof-edge runs
155.55 ft
Stock pieces rounded per independent run
18 pieces
Area-based field-material budget
$2,937.66
Illustrative field purchasing weight
4,320.08 lb
Illustrative field purchasing weight
2.16 US short tons
Updates as you adjust your numbers

An estimate, not a quote. Example rates are adjustable. See the assumptions below.

Estimate basis

Field bundle coverage is product-specific. The area budget and optional rounded bundle budget are alternative material budgets, not amounts to add together.

Underlayment uses its own effective coverage, layers, and allowance. It does not inherit field-material waste. Edge pieces are rounded per independent run; no pooled offcut reuse is assumed.

Weight is an illustrative area-based purchasing weight including field allowance. It is not installed dead load, disposal tonnage, or a structural capacity check.

Behind the numbers

How this calculator works

Expanded length Le = L + 2O and width We = W + 2O. Actual area = Le × We × sqrt(1 + (pitch/12)²); flat uses factor 1. Known area passes through unchanged. Purchasing area = actual area × (1 + field allowance/100); squares = area/100. Asphalt bundles = ceil(purchasing area × nominal bundles/100), or ceil(purchasing area / actual bundle coverage). Underlayment rolls = ceil(actual area × layers × (1 + separate allowance/100) / effective roll coverage). Each positive edge run r needs one piece if r ≤ stock S, otherwise ceil((r − lap)/(S − lap)); add pieces across independent runs.

A worked example

A 40 × 30 ft gable with 1-ft horizontal overhang and 6/12 pitch has 42 × 32 ft projection and 1,502.63768088 sq ft actual surface. At 15% field allowance: 1,728.03333301 sq ft, 17.28033333 purchasing squares, and 52 nominal-three-per-square bundles. At $170/square, the area budget is $2,937.66. One underlayment layer at 400 effective sq ft/roll and no extra allowance needs four rolls. Two 42-ft eaves and four 17.88854382-ft rake half-runs need 18 ten-foot edge pieces at zero example lap, not the 15 obtained by pooling a rectangular perimeter.

Assumptions & what’s included

  • Simple rectangular, uniform-pitch roofs only. Length and width are outside-wall dimensions. Horizontal overhang is added on all four sides, including gable ends. Gable ridge follows entered length even when width is larger. Equal-pitch hip geometry normalizes the longer and shorter expanded dimensions. Shed mode slopes across entered width; flat mode ignores pitch.
  • Known actual sloped area includes measured slope and overhang; hidden dimensions and pitch are inactive. Area alone cannot establish perimeter, ridge, hips, starter, or gutter runs. For dormers, valleys, mixed pitches, intersecting roofs, or nonrectangular plans, use separately measured nonoverlapping surfaces and independent accessory measurements. Do not climb onto a roof to obtain inputs; use reliable drawings or qualified measurement.
  • A roofing square is 100 sq ft, not a bundle. Actual area excludes purchasing allowance. Package counts use full-precision demand and round upward without subtracting an epsilon. Exact decimal comparisons and squared geometry avoid rounding pitch factors before purchase decisions. Changing display units preserves the physical measurement.
  • The 15% field allowance is an editable example, not a roof-specific recommendation. Field bundles, dedicated caps, starter, and underlayment are separate scopes. Effective product coverage must already include applicable laps; do not count the same lap or waste twice.
  • Underlayment starts with actual roof surface, not field purchasing area. Example coverage is 400 sq ft per roll with one layer and zero additional allowance. Verify the selected product and assembly. No universal minimum slope, underlayment layer count, fastening pattern, or product suitability is certified.
  • Money is displayed to cents, quantities to at most two decimals, and package counts as whole purchases. Full precision is retained before display. Prices and weights are illustrative editable inputs, not verified current local quotes or structural engineering advice.
  • Default area-based $/square and lb/square: asphalt 170/250; metal 600/100; tile 800/900; slate 1500/700; TPO/EPDM 500/50. Material selection resets these example allowances; edit them for a real product. Only asphalt shows bundles. Other coverings require actual panel/tile/membrane specifications and layouts.
  • Gable edges are two expanded-length eaves plus four sloped half-width rakes. Shed edges are two expanded-length sides plus two sloped full-width sides. Hip edges follow the expanded horizontal rectangle. Flat and known-area modes do not infer shingle edge stock. Enter applicable independently measured runs; identical runs may be grouped. Stock and lap share explicit units, lap must be shorter than stock, and no offcut reuse or corner-fitting layout is promised.
  • The material budget is area-based and excludes installation and accessories. The optional bundle budget rounds field purchases first; it is an alternative, not an additional charge. US short tons use 2,000 lb.

A few common questions

Can one roofing square always be bought as three bundles?

No. A square is an area of 100 sq ft. Many shingles use three bundles, but product coverage varies. Enter the actual nominal bundles per square or wrapper coverage. Non-asphalt coverings do not receive asphalt bundle counts.

Why are edge pieces rounded by run?

Pooling total perimeter assumes offcuts can always cover other runs and ignores slope and joints. This estimate rounds each independent run and accounts for entered laps; a contractor still needs to review corners and a real cutting layout.